ERICSSON RBS 6601 PDF

WCDMA RAN Systems and Site Introduction. RBS components. WCDMA RBS Maintenance. 2. Customer Product Information (CPI) and. TXO Systems has the ERICSSON RBS RRUS 12 B3 in stock, along with a wide range of used and refurbished telecommunications equipment from all. Ericsson shall have no liability for any error or damage of any kind resulting from The support system for the RBS main unit is available in two variants.

Author: Momuro Baramar
Country: Timor Leste
Language: English (Spanish)
Genre: Love
Published (Last): 14 February 2004
Pages: 104
PDF File Size: 5.16 Mb
ePub File Size: 14.18 Mb
ISBN: 929-1-92466-963-7
Downloads: 67092
Price: Free* [*Free Regsitration Required]
Uploader: Yozshurg

Some red indicators may flicker during startup. Exhaust air from the rear may not be allowed to circulate to the front air intake in the rack. Remove the protective caps from the connectors on the cables and the XMU. Route the cables to the main unit using the rail openings and connect them according to the cabling instructions. Rvs to main content.

Support system variant 2 supports all DUW versions. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab.

Sign in to check out Check out as guest. Be careful if the installation requires pulling the cables. Insert the TCU in slot 2 in the main unit. These are shown in the document Trademark Information. To connect the GPS solution: Connect the alarm signal wires to the alarm rricsson by inserting each wire into each dedicated tension clamp connection and check that they are properly fastened.

  BARBARA JAROSZEWSKA KOSMETOLOGIA PDF

RBS_Installation_Instructions | 正倫 賴 –

If applicable, check that the optical indicators next to the optical cables interfaces on the DU are flashing. Table 2 lists the cross sectional area requirements for variant 2 power cables. Please enter a valid ZIP Code. Follow the instructions in Section 6 on page 13 when installing the two support systems in the rack.

Shipping cost cannot be calculated. Switch off or disconnect any external battery back-up. Place the main unit in the rack and tighten the rack screws on the brackets according to the rack supplier’s specification. Information about on-site space requirements can be found in RBS Description and in the manual for the rack. Align the connector with the cable protective cap and tie the cable with the cable strap as show in numbers 1 and 2 in the following figure.

Ericsson RBS 6601 LTE Indoor Main Unit Remote Base Station 1/bfl 901 009/4

Detailed information is found in Hardware Maintenance Instructions. The cable connections depend on the transmission alternative chosen for the specific site.

Examine the packaging for damage. Place the brackets in the proper position: Disclaimer The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Resume making your offerif the page does not update immediately.

To adjust the main unit using standard ericdson See all electronauts has no other items for sale.

Insert the power cable wires into each dedicated tension clamp connection and check that they are properly fastened. The connector is keyed so that only one end fits into port SAU on the support system. You are free to manage this via your browser settings at any time.

  BULLETIN 194E PDF

Check that all red optical indicators are off, and that the rest rbss the optical indicators are lit as they should according to Indicators, Buttons, and Switches. Handle the optical cables with care and do not exceed the minimum bending radius the fiber bending radius shall never be less than 30 mm. To install the main unit in a inch rack: It may take up to 10 minutes before all units in the cabinet are in operation. Once the power is switched on, the boards load with their specific software.

To connect the RBS to the twisted-pair cables: Have one to sell? Never look directly into the end of an optical cable, or other laser source. Optical indicators show the board status.

BTS FOR ERICSSON RBS – BFL /1 R3A – DUW 20 01 – KDU /2 R3B | eBay

LMT B by Default. The external transmission cables are connected to the DU. Make sure that the cable connectors and the connectors on the XMU are clean. Install the railings on the main unit and tighten the M4 screws in the brackets to a torque of 1. Take care not to damage the front when handling the main unit.