BlueAnt. 3. V1 USER GUIDE. Introduction. The revolutionary BlueAnt V1 This manual focuses on how to use your headset with your Bluetooth enabled phone. View and Download Blueant Q1 user manual online. Q1 Headsets pdf manual download. Package Contents: BlueAnt V1x, rubberised metal ear hook, translucent ear USB cable, AC power adaptor, quick start guide, user manual, warranty card.
|Published (Last):||12 April 2004|
|PDF File Size:||3.2 Mb|
|ePub File Size:||2.46 Mb|
|Price:||Free* [*Free Regsitration Required]|
Page 28 Switching Between Calls and Phones If you have two phones connected to the Q1, uswr you receive a call on one of them while you are already on a call on the other phone, then you can use the Q1’s buttons to answer the second call.
BlueAnt V1x Voice Controlled Headset User Manual | 28 pages | Also for: V1 Voice Controlled Headset
The online user guide contains all the information from the Quick Start Guide plus much more, including tips and tricks to help you get the most out of your BlueAnt device, details of how to access the advanced features and functions of your device, and troubleshooting information with advice on solving common problems you might encounter.
Table of Contents Add to my manuals Add. Page 40 You can also use this function to disconnect the Q1 if you are not on a call, although in this case you will not be able to reconnect to the Q1 by clicking the buttons again to reconnect in this case, you can use the “Am I Connected” This section describes some typical problems you may encounter, and explains how to solve them.
The voice prompts will explain that the Q1 is now in pair mode. Introduction Welcome to the Q1 user manual. Charging the Q1 Your Q1 has been given an initial charge to get going, but in future you will need to charge it for up to 2. To use the Q1, you need to pair it with your phone. This command dials the number of the last incoming call received on the Q1 headset it doesn’t matter which phone was connected to the Q1 at the time the call was received.
When the level is set to “High” the commands you give the Q1 will need to match the speech pattern it is expecting more exactly, while “Low” You must wait for the Q1 to finish reading the commands before you can say one of the commands. When the light goes blue, the Q1 is fully charged. Having Problems with your Q1? Gently press the replacement gel onto the Q1, and push it on firmly to secure it in place. Sensitivity Level Q1 has been configured to recognize.
You cannot turn the Q1 off during a call, so you must end the call first. If you receive a call while you are already on a call, and your phone and phone network both support call waiting, then you can use the Q1 buttons to either end your current call or put it on hold and take the incoming call.
Noise Reduction and Voice Isolation To ensure that you can always be heard, even in the noisiest of environments, the Q1 comes with BlueAnt’s Voice Isolation Technology, which is designed to eliminate background noise and reduce wind noise. You can change it by accessing the Q1’s “Settings Menu”.
Pairing Your BlueAnt
If you want to change the ear gel, you can remove it by gently lifting it away from the Q1. When you have two phones blueatn you can answer whichever one rings. Don’t have an account?
The pairing process is similar to the process of pairing a phone. General Advice If you are having problems with your Q1, the first thing to try is to reset the device, and start again: Don’t show me this message again. If you haven’t already fitted it, locate the ear hook that came in the box with your Q1, and attach it “Wearing the by pushing the smaller end of the hook through the hole on the back of the Q1.
Getting Started To use the Q1, you need to pair it with your phone. The Q1 allows you to switch back mabual your phone at any time, even while you are on a call. Buttons And Microphones The following diagram shows how you should attach the ear hook if you want to wear the Q1 in your right ear.
Page 38 Standby Q1 is switching off. Page 7 The online user guide contains all the information from the Quick Start Mmanual plus much more, including tips and tricks to help you get the most out of your BlueAnt device, details of how to access the advanced features and functions of your device, and troubleshooting information with advice on solving common problems you might encounter.
Use the “Settings Menu” command to access the following options. The following diagram shows how you should attach the ear hook if you want to wear the Q1 in your right ear. Enter text from picture: What Does It Mean? The Q1 will read out the number of the last incoming call and ask you which calling command you want to tag it to.
You can set this to “High”, “Medium”, or “Low”. If you are looking for help with your Q1 headset, then you’ve come to the manuwl place.
Overview These voice commands get you to everything you need to use the BlueAnt Q1.
There are two modes of voice isolation. Setting Up Speed Dials For example, if you use the command “Call Speed Dial 3” and you have stored a number in the Q1’s speed dial 3 setting, then the Q1 will call this number.
These manua, commands get you to everything ueer need to use the BlueAnt Q1. If you are on a call when you click the buttons, then the audio will be transferred back to your phone where you can continue the call.