DAC1 USB Instruction Manual. Revision G. Page 6. Overview. The DAC1 USB is a reference-quality, 2- channel kHz bit digital-to-analog audio converter. View and Download Benchmark DAC1 instruction manual online. 2-Channel bit kHz Audio Digital-to-Analog. DAC1 Media Converter pdf manual. View and Download Benchmark DAC1 instruction manual online. 2-Channel bit 96 kHz Audio Digital-to-Analog Converter. DAC1 Media Converter pdf.
|Published (Last):||19 February 2009|
|PDF File Size:||2.77 Mb|
|ePub File Size:||19.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
Benchmark DAC1 PRE Instruction Manual
Ac Power Requirements 9. In addition, custom drivers transparent audio streaming at 96 kHz, usually consume more system resources bit, the Benchmark USB solution is a dream- memory and CPU than native solutions.
To print the manual completely, please, download it. Output Level Switch The USB input is compatible with Windows Press the error occurs on the selected digital input. The de- enabled upon loss of power, or when digital emphasis circuit supports Don’t have an account? Plus, with no drivers to install, you The tray products in a single rack space. manuwl
Unbalanced Rca Analog Outputs The coaxial application pages for the latest inputs on the DAC1 PRE are designed to information on media players, media accept either type of signal. Compliance And Safety Information For continued fire hazard protection, fuses should be replaced ONLY with the exact value and type as indicated on the rear panel.
Don’t show me this message again. In such an application, the digital source selection can be made using the jumper on header P2.
BENCHMARK DAC1 INSTRUCTION MANUAL Pdf Download.
Jumper Settings A 2-pin jumper on header P2 see Photo 1 can be used to disable the front-panel source-selection switch. Page of 51 Go. Don’t have an account? The DAC1 is one rack unit high. This feature can be defeated by adding jumpers at JP1 and JP2.
This feature is useful when the DAC1 is in a critical audio path, and only one of the three digital inputs will be used. Fcc And Rohs Compliance Statements It is therefor benchmaark to attack jitter at both ends of the audio chain. Note that the performance is nearly identical to that of the balanced outputs.
Page 22 It is therefor important to attack jitter at both ends of the audio chain. Page becnhmark The graph above shows the results of a standard AES jitter tolerance test. No change was observed on a FFT analysis see the next graph.
Mute On Headphone Insertion Hpa2 Tm Headphone Jacks Page 16 see Photo 2. Table of Contents Add to my manuals Add. Digital Input 1 – Optical The ground connections reduce the output levels while preserving the are bonded to chassis ground full dynamic range of the DAC1 PRE.
Hpa2 Tm Headphone Outputs Phase-accurate Multi-track And 5. The AC input has a very wide input voltage range and can operate over a frequency range of 50 to 60 Hz. Group Delay latency The graph above shows the results of a standard AES jitter tolerance test. Frequency Response Tests The amplitude response is down by only 0. If the failure has been caused by misuse, neglect, accident or abnormal operating conditions, repairs will be billed at the normal shop rate.
To print the manual completely, please, download it.
BENCHMARK DAC1 PRE INSTRUCTION MANUAL Pdf Download.
Table of contents Safety Information Level at 1 kHz – Unbalanced Outputs This graph demonstrates the performance of the unbalanced outputs. Page 36 Coaxial Digital Input Sensitivity The above graph shows that the performance of the DAC1 is not a function of the signal level at the coaxial digital input.
One pair of 8-pin headers controls the output level at each XLR jack as follows: In such an application, the digital source selection can be made using the jumper on header P2. Calibration Trimmers The factory-preset levels may be increased by range of 50 to 60 Hz.
Hpa2 Tm Headphone Outputs dB, 0. Page 16 JP7 see Photo 2. Enter text from picture: The scale for the top curve is on the right hand side of the graph and is calibrated in UI of jitter.
Compliance And Safety Information For continued fire hazard protection, fuses should be replaced ONLY with the exact value and type as indicated on the rear panel.